Introduction: Delivery Rhythm Stuck at Back‑End Inspection
A silicon photonic module team recently advanced an 800G project. The yield of silicon lenses fabricated through wafer processing was good, but the delivery rhythm on the module factory side remained difficult to align – after dicing, lenses queued for inspection, then queued for sorting, and upon arrival at the module factory still required re‑inspection. Back and forth, the delivery lead time was stretched out.
The team lead noted: wafer processing has already brought costs down to a reasonable level, but whether the device side can deliver stably – the bottleneck is not at the wafer fab, but at back‑end inspection.
This is not an isolated case. After silicon lens wafer process scaling, large‑scale stable delivery on the device side is becoming a new challenge.

I. What Exactly Are the Delivery Constraints on the Device Side?
For optical communication device makers (optical module factories, silicon photonic module factories), the delivery of silicon lenses appears on the surface to be a question of quantity – but in reality, it is three hard constraints that must hold simultaneously:
1. Yield Constraint
Pass rates across batches must remain stably high, with no batch‑to‑batch fluctuation permitted.
2. Consistency Constraint
Surface form PV/RMS and roughness Ra within and between arrays must fall within a narrow window – otherwise module coupling efficiency will fluctuate.
3. Delivery Lead Time Constraint
Demand is being pulled rapidly from 400G to 800G. If lens arrival is delayed by one week, module delivery is delayed by one week.
The three constraints compound: what the device side requires is not occasional inspection data, but stable delivery backed by data for every batch and every single lens.
II. Three New Challenges on the Device Side After Wafer Process Scaling
Wafer processing has reduced production‑side costs and improved efficiency – but once the device side takes over, three new challenges emerge:
1. Post‑dicing unit counts surge, inspection capacity is insufficient
A single wafer yields tens of thousands of lenses after dicing. What is received from the wafer fab is a batch‑level pass conclusion; what the device side needs is a per‑lens pass record. Inspection workload has increased by an order of magnitude compared with the small‑piece, small‑batch era.
2. Array consistency requirements are higher
Wafer‑level processes inherently demand high array density. Surface form differences between adjacent lenses must be confirmed lens by lens – sampling is no longer accepted by module factories.
3. Delivery lead times are being compressed
The delivery windows for 800G silicon photonic modules continue to shorten. The lens‑side inspection cycle directly consumes the available time on the module side.
III. How Can the Inspection Stage Become a Delivery Stabiliser?
For the device side to achieve large‑scale stable delivery, the key is to transform inspection from a bottleneck into a stabiliser – with sufficient takt time, complete data, and timely response.
Breaking the device‑side delivery chain into stages, let us examine the role of inspection in each:
Within this chain:
IV. Inspection Solution Matched to Device‑Side Delivery
The Mingcha Zhixin Qiuhao R Series is designed around this scenario, employing reflective laser interferometric non‑scanning imaging to directly acquire a full‑field 3D point cloud in a single exposure.
Core characteristics:
Reflective laser interferometric non‑scanning imaging – no Z‑axis mechanical reciprocating scanning
Under specific sample and test conditions, approximately 1 second per lens; approximately 3 hours for 10,000 lenses
Vertical resolution 0.5 nm
Stitching error < 0.5 μm
Built‑in data archiving capability supporting per‑lens traceability and full inspection report output
Service response: 48‑hour on‑site arrival, solution provided within 72 hours, local spare parts delivery within 3–5 days (subject to specific service terms)
Note: The above accuracy, takt time, and stitching data are based on specific samples and test conditions. Actual results vary by sample and application environment.

V. Conclusion
After silicon lens wafer process scaling, the real bottleneck for large‑scale stable delivery on the device side is not at the wafer fab – it is whether back‑end inspection can keep up.
An inspection device with approximately 1‑second takt time, capable of continuously measuring tens of thousands of lenses, with traceable data and timely service response, is the key infrastructure for the device side to convert "wafer‑level capacity" into "module‑level delivery."
The Mingcha Zhixin Qiuhao R Series is designed precisely around this scenario: reflective laser interferometric non‑scanning imaging, approximately 1 second per lens, approximately 3 hours for 10,000 lenses, vertical resolution 0.5 nm, stitching error < 0.5 μm, 48‑hour on‑site arrival, solution within 72 hours, local spare parts delivery within 3–5 days (subject to specific service terms).
This article is compiled based on industry application scenarios, intended for selection reference only and not constituting procurement advice. Parameters, takt time, and service policies are subject to the manufacturer's latest official information and empirical results.
- Share
-
12
- Chip continues to be in short supply! Large factories accelerate the expansion of production or boost the demand for semiconductor equipment
- Updating...