Affiliation: Shenzhen Qianhai Yuzhuo (Apex) — Authorized Distributor of PILLAR Corporation
Meta description: PILLAR (Japan) NCC/PCP porous carbon vacuum chucks use proprietary sintered porous carbon for full-surface vacuum holding and non-contact transport of wafers, LCD glass and thin films. 10 µm-class flatness, a sub-1500 g Ø300 all-carbon pad, zero particle generation and no static charge — outperforming conventional ceramic chucks. Authorized distributor: Shenzhen Qianhai Yuzhuo (Apex).
Models: Porous carbon pad NCC/PCP (C68 for non-contact use, F64 for vacuum chucking); all-carbon precision vacuum chuck PCP (up to Ø450 mm)
All-carbon precision vacuum chuck PCP — vacuum chucking, supports Ø450 mm wafer-scale holding
Core Value
PILLAR Porous Carbon Precision Chuck NCC/PCP — proprietary sintered porous carbon for full-surface holding and non-contact transport, superior to ceramic chucks.
· Uniform pores, full-surface holding: controlled macro-pore size and porosity let fluid pass evenly across the entire surface, so the pad holds precision workpieces uniformly and flatly, without tilting.
· 10 µm-class flatness: the carbon surface is precision-polished to ~10 µm flatness, satisfying precision fixation for wafers, LCD glass and high-performance films that must not tilt.
· Extreme light weight: specific gravity only 1.2–1.7; the all-carbon Ø300 chucking pad weighs under 1500 g, greatly supporting machine lightweighting and high-speed operation.
· No particles, no static charge: after high-temperature treatment impurity concentration is near zero; after ~15 minutes of use particle generation is negligible. Carbon is a good conductor, so workpiece static is discharged during chucking.
· Better than ceramic: lighter, more uniform temperature (Δt = 3.7 °C vs ceramic 9.9 °C), thermal-shock resistant, black high-contrast surface; flatness unchanged after 100,000 chucking cycles.
· Two grades: C68 for non-contact use (high permeability, no residual pressure, fast clamp/release), F64 for chucking; fluororesin/epoxy coatings and bonded large-format fabrication available.
Product Description
Since establishing the TANKEN brand in 1955, PILLAR (Japan) has long developed carbon rings for mechanical seals, and over 50-plus years commercialized high-strength porous carbon technology — producing porous carbon, porous silicon carbide and porous tungsten carbide. The Porous Carbon Pad is a breathable sintered porous carbon built on high-strength mechanical-grade carbon; with controlled pore distribution and porosity it provides uniform permeability, and has become the precision holding device for semiconductor wafers, LCD glass, high-performance films and optical media where tilting is prohibited.
1. Operating Principle and Technical Breakthrough
By controlling macro-pore size and porosity of the sintered carbon, gas/liquid passes uniformly across the whole surface:
· Chucking mode (negative pressure): after evacuating the porous carbon pad, the workpiece is firmly held to the carbon surface. Uniform pores give even full-surface attraction for high-precision, flat holding.
· Non-contact mode (pressurized): after passing pressurized gas, the workpiece floats slightly above the carbon surface for non-contact transport; using the C68 grade suppresses air consumption.
· Fast response: C68 is highly permeable; no residual pressure builds inside the carbon, enabling rapid clamp and release.
2. Performance and Precision Parameters
· Flatness: precision-polished to ~10 µm-class flatness; the all-carbon PCP vacuum chuck supports Ø450 mm wafer-scale sizes.
· Weight: all-carbon Ø300 chucking pad under 1500 g.
· Metal contamination: per a 12-inch clean-wafer chuck/release test, wafer metal contamination is ~10¹⁰ atoms/cm².
· Ultimate vacuum: with a wafer loaded, differential pressure ≥40 kPa; a 50 L/min pump reaches limit in ~0.6 s, a 180 L/min pump in ~1.8 s.
· Compressive strength: Ø100 PCP compressive strength 2.3 MPa; Ø300 PCP flatness unchanged after 100,000 "chuck ⇔ release" cycles.

12-inch porous carbon chuck flatness test result (CMM report)
3. Materials and Product Applicability
· Two grades: C68 (non-contact use, bulk density 1.2, Shore hardness 65 Hs) and F64 (chucking use, bulk density 1.5, Shore hardness 47 Hs).
· Workpieces: semiconductor silicon wafers, FPD LCD glass, CD/DVD optical media, high-performance films.
· Product forms: chucking pad (vacuum precision holding), non-contact pad (pressurized float transport), air/water diffuser plates, filters.
· Manufacturable sizes: square plates up to □250 mm, round plates up to Ø350 mm, thickness up to 100 mm; carbon-surface coatings (fluororesin/epoxy) and bonded large products available.
8-inch porous carbon chuck flatness test result (CMM report)
4. Core Value and Application Benefits
· No workpiece damage: moderate hardness and good self-lubricity avoid damaging workpieces; also suited to conductivity and anti-static measures.
· Machine-vision friendly: natural uniform black carbon with no color mottling gives no halation and high contrast for image inspection.
· Broad chemical resistance: structurally and chemically stable, resistant to nearly all chemicals; environment is not restricted.
· Upgrade replacement: for almost all current porous-body applications, porous carbon offers equal or better properties and can upgrade-replace existing materials.
NCC porous carbon pad — non-contact float and full-surface chucking product series
Key Advantages
(1) Compared with Ceramic Chucks: Lightweight, Particle-Free, Anti-Static, More Uniform Temperature
Evaluated by a third party (Renesas Naka semiconductor), the all-carbon PCP chuck outperforms conventional ceramic chucks on multiple key metrics:
Item | Ceramic chuck | PCP (all-carbon) chuck |
Bulk density (light weight) | 2.5 / 3.9 g/cm³ | 1.3 / 1.8 g/cm³ (significantly lighter) |
Particle generation | Continuous particle emission | Nearly zero particles ~15 min after start of test |
Debonding (tape peel) | Particle shedding | Fluororesin-coated PCP: no carbon particle shedding; 100 consecutive peels, no release |
Chucking-surface temperature distribution (hot plate 150 °C) | Δt = 9.9 °C | Δt = 3.7 °C (more uniform) |
Charging | Near insulator, easily charged | Conductive, no charging; static discharged during chucking |
Thermal shock | Weak | 150 °C into cold water with no abnormality; flatness 9 µm unchanged after 5 cycles |
Metal contamination | — | ~10¹⁰ atoms/cm² wafer contamination after chuck/release |
Ultimate vacuum | — | Differential pressure ≥40 kPa; 50 L/min pump reaches limit in ~0.6 s |
Compressive strength | — | 2.3 MPa (Ø100 PCP); flatness unchanged after 100,000 cycles |
Reflectance | Relatively high | Black, 5–10% in visible range; high image contrast |
UV resistance | — | 280–300 nm, 255 W/m² for 100 h, no degradation |
(2) Precision Polishing and High Flatness
The pad surface is precision-polished to 10 µm-class flatness, and is valued as the precision holding device for wafers, LCD glass, high-performance films and optical media where tilting is prohibited.
(3) Cleanliness and Long Life
· Every process from material to parts to finished product is cleaned to effectively remove particles; carbon grain boundaries are highly bonded, so friction particles from passing air do not shed.
· Thick-walled porous carbon forms ultra-high wear resistance under severe conditions with low friction, maintaining Shore hardness ≥47 while not mating against the counterpart material.
Technical Specifications
Item | Parameter |
Product grade | C68 (non-contact use) / F64 (chucking use) |
Bulk density | C68 = 1.2 / F64 = 1.5 g/cm³ |
Shore hardness | C68 = 65 / F64 = 47 Hs |
Flexural strength | C68 = 35 / F64 = 21 N/mm² |
Compressive strength | C68 = 110 / F64 = 95 N/mm² |
Young's modulus | C68 = 1.1 / F64 = 5.6 kN/mm² |
Poisson's ratio | 0.2 / 0.3 |
Volume resistivity | C68 = 54 / F64 = 100 µΩ·m |
Thermal expansion | C68 = 5 / F64 = 6.5 ×10⁻⁶/K |
Thermal conductivity | C68 = 3 / F64 = 1.1 W/(m·K) |
Heat resistance (in air) | 300 °C |
Average pore size | ~5 µm |
Porosity | ~35% |
Manufacturable sizes | Square plates up to □250 mm, round plates up to Ø350 mm, thickness up to 100 mm |
Flatness | ~10 µm class (all-carbon PCP supports Ø450 mm) |
All-carbon Ø300 pad weight | <1500 g |
Compressive strength | 2.3 MPa (Ø100 PCP) |
Ultimate vacuum differential pressure | ≥40 kPa |
Note: the above is compiled from PILLAR porous-carbon specification products and comparative ceramic-chuck data. Workpiece dimensions, holder material and non-contact / chucking / dual-use configuration are customized after consultation.
Applications
Semiconductor Wafers
· Full-surface vacuum chucking and non-contact transport of 8-inch/12-inch silicon wafers.
· Low-damage, anti-static stages for wafer back-grinding, lithography and inspection.
LCD / OLED Panels
· Flat holding and image-inspection stages for FPD glass and high-performance films.
· Precision chucking and air/water dispersion in panel processes.
Data Storage and Optics
· Smooth transport and holding of CD/DVD optical media and optical films.
· High-contrast black surface suits image diagnostics and AOI inspection.
Other Precision Machining
· Air-bearing, filter and air-diffuser components using the porous-body principle.
· Upgrade replacement where existing ceramic/porous materials are insufficient.
FAQ
Q: What advantages does the porous carbon chuck (PCP) offer over a conventional ceramic chuck?
A: The all-carbon PCP is lighter (bulk density 1.3–1.8 vs ceramic 2.5–3.9 g/cm³), emits almost no particles after ~15 minutes, is intrinsically conductive and non-charging, gives a more uniform chucking surface temperature (Δt = 3.7 °C vs ceramic 9.9 °C), survives 150 °C sudden cold-water quenching without cracking, offers high black-surface image contrast, 2.3 MPa compressive strength, and unchanged flatness after 100,000 chucking cycles.
Q: How do I choose between the C68 and F64 grades?
A: C68 is the non-contact grade — highly permeable with no residual pressure inside the carbon, suited to pressurized-float non-contact transport. F64 is the chucking grade — suited to full-surface vacuum holding after evacuation. Choose by whether the process needs "vacuum holding" or "non-contact transport", or both.
Q: Does the porous carbon chuck shed particles or cause metal contamination on wafers?
A: The carbon is high-temperature treated to near-zero impurity concentration; a particle counter shows almost no particles ~15 minutes after start. A 12-inch clean-wafer chuck/release test shows wafer metal contamination of ~10¹⁰ atoms/cm², meeting semiconductor cleanliness requirements. The fluororesin-coated version further prevents carbon-particle shedding.
Q: How large can the chuck be made? Is customization available?
A: Standard manufacture covers square plates up to □250 mm, round plates up to Ø350 mm and thickness up to 100 mm; the all-carbon PCP vacuum chuck already supports Ø450 mm. Large products can be fabricated by bonding, with fluororesin/epoxy carbon-surface coatings. Please specify workpiece size, holder material, and non-contact / chucking / dual-use requirements when ordering.
Q: Is porous carbon chemically resistant, and can it be used with wet processes?
A: The structure is chemically stable and resistant to nearly all chemicals, so the use environment is not restricted. Combined with its self-lubricity, low particle generation and anti-static conduction, it is well suited to wet cleaning, coating and developing stations where ceramic chucks risk particle shedding or static damage.
Shenzhen Qianhai Yuzhuo (Apex) — Authorized Distributor of PILLAR Corporation
WeChat: qhyz1303 / Tel: +86-755-26609876 / Email: qhyz@apexe.net / Web: http://www.apexe.net/